The Customer Name on the Traveler

A customer is named. Your shop tag uses a shorter name. You pull the half-printed lot sheet from the slot at Traveler Desk, run a finger along the typed full legal name at the top left, and cross-reference it to the hand-scrawled shorthand printed on the steel bar stock sitting on your bench. You don’t move to set up the mill until you confirm the two names map to the same client, even if you ran the same lot for this client last week.

Full client naming conventions for this lot

The full name printed at the top of the traveler is the only official identifier for invoicing, export compliance, and material sourcing records tied to this lot. Any deviation, even a missing “Inc.” or misspelled street suffix, can cause delays in post-processing if it does not match the purchase order on file with the front office. The name is pulled directly from the client’s submitted purchase order, so you don’t edit it unless you receive a formal written revision from the operations team, even if you know the client rebranded six weeks prior. This official name also dictates which material batch is allocated to the lot, per client-specific sourcing requirements listed in the shop’s master order database.

The Customer Name on the Traveler
A tag and a wire, stamp turned away.

Shorthand code cross-reference steps

Every active client is assigned a unique 3-character shorthand code to simplify on-bench identification without exposing sensitive client information across the shop floor. You follow these steps to confirm the code matches before you begin any machining work:

  1. Locate the 3-character shorthand printed on the raw stock tag tied to the left end of your bar stock.
  2. Find the matching 3-character code printed in parentheses directly to the right of the full customer name at the top of the traveler.
  3. Cross-reference both codes to the printed master code list taped to the upper right corner of your mill control panel.
  4. Confirm no other active lot in your queue uses the same shorthand code for a different client.
  5. Initial the small line next to the shorthand code on the traveler before you load any stock into the mill.

Illustrative example: The full legal name “Northwest Aerospace Fabrication Co.” maps to the 3-character shorthand “NWA” printed on all stock and shop tags for this client’s 14 active orders this quarter, per the master list updated last month. This step prevents you from accidentally machining stock for one client to the specs of another, even if the part dimensions look identical at first glance.

Name mark placement on finished part blanks

After you finish the first milling operation on each part blank, you stamp the 3-character shorthand code in the designated non-critical surface area noted on the traveler’s dimension diagram. You only stamp the shorthand, not the full customer name, to avoid exposing client information if the part is sent out for secondary coating or heat treating at a third-party facility. The stamp must be deep enough to remain legible through all post-processing steps, but not so deep that it cuts into the 0.5mm tolerance buffer for the part’s exterior surface. You count the number of marked blanks after you finish stamping, and write that total in the blank field next to the part number on the traveler before you set the blanks in the completed operations bin by your bench.

Discrepancy flagging process for mismatched tags

If the shorthand code on the stock tag does not match the code on the traveler, you do not machine any of the stock, even if a lead hand tells you it’s a simple printing error. You place a bright red flag sticker directly over the customer name field on the traveler, write the mismatched codes and the lot number on the sticker, and carry the entire lot of stock plus the traveler to the front office for verification before you proceed with any work. You don’t move the lot to another operator’s bench or leave it unattended while you wait for verification, to avoid mix-ups with other active lots in the shared work area. If the discrepancy is confirmed to be a stock labeling error, you get a formal printed correction slip to tape to the back of the traveler before you begin work, even if the front office gives you verbal confirmation first.

Approval signature field requirements for this stage

Once you complete all machining operations for your assigned stage, you sign and date the middle signature field on the right side of the traveler, directly below the line marked “First Operation Complete”. You don’t sign the field until you’ve inspected the first three finished blanks with your digital calipers to confirm they meet all listed dimensions for your stage of work. You also write the average measured dimension for the critical bore hole on the line next to your signature, so the next operator can quickly confirm your work falls within spec before they begin their operations. You do not initial any other signature fields on the traveler, even if the next operator is out for the day and you are asked to cover their portion of the work, as each signature is tied to a specific stage of the lot’s processing and accountability tracking.

Next instance you pull this lot sheet for part finishing

When you pull this same traveler again for the final deburring and polishing stage, you first re-verify that the shorthand code on the part blanks matches the code on the traveler, even if you were the one who stamped the code earlier. You cross-check the total number of parts listed on the traveler against the number of parts in the bin, to account for any parts that were pulled for quality testing or scrapped during the secondary heat treating process. You look for the correction slip taped to the back of the traveler if you flagged a discrepancy earlier, to confirm the lot was properly verified before you begin the final work. You also check the signature fields to confirm all prior stages of work are signed off before you start any finishing work, to avoid wasting time on parts that failed inspection at an earlier stage. This second check of the customer name and shorthand code takes less than 30 seconds, and eliminates the risk of finishing parts for the wrong client that would have to be scrapped at the shop’s cost. You keep the traveler tucked in the side pocket of the part bin as you work, so you can reference it quickly if you notice any irregularities with the part dimensions or markings as you go.

About · Contact · Privacy · Disclaimer · Advertising · Terms