The cert says the condition the metal was supplied in. The traveler does not repeat it. You reference the cert directly at your bench before you make the first cut on this lot of 4130 bar stock. You line the cert’s lot number up with the stamp etched on the end of the bar to confirm you are working with the correct material. No discrepancies in that match mean you move forward with the steps outlined on this sheet.
Lot-specific supply parameters listed on this form
This form pulls only the supply condition data points that directly impact your milling operation, cutting out the extraneous lab test data and compliance notes that do not affect your setup or cutting process. You will find the material hardness range, surface roughness rating, and maximum allowed bow or twist for the bar stock listed in the top third of the page, organized in the order you will reference them during setup. You do not need to source additional data from the cert for your work, as all relevant values are transcribed here for this specific lot, but you still cross-reference with the physical cert to confirm no transcription errors were made when the form was created. If you spot a mismatch between the values listed here and the values on the cert, you flag the form for the production coordinator to correct before you proceed with any setup work.

Cross-reference notes for this work order sheet
You pull the corresponding material cert from the folder you picked up at Traveler Desk earlier this shift, no need to cross-reference digital records for this lot as long as the physical cert matches the parameters listed here. Follow these steps in order to complete the cross-reference before you adjust your machine:
- Match the lot number printed on the top right of this work order sheet to the alphanumeric stamp on the bar end, checking that every digit matches, including the two-letter suffix that denotes the specific heat treatment batch the bar was pulled from.
- Align the supply condition listed on the cert to the note in the left margin of this sheet to confirm you have the correct hardness range for the part you are milling, adjusting your tool feed rate and spindle speed accordingly if the hardness falls at the higher or lower end of the expected range.
- Cross out any pre-printed feed rate suggestions on this sheet if the cert lists a hardness 5 points higher or lower than the standard value used for the template, writing in your adjusted feed rate directly next to the crossed-out text so the next operator can see the change immediately.
- Initial the top left margin of this sheet once you confirm all cross-references align, no exceptions for partial matches or lots that look identical to ones you ran earlier in the week.
If you find a mismatch at any step, you flag the lot for a material coordinator to review before you make any adjustments to your machine setup. You never proceed with machining if the lot number does not match exactly, even if the material grade appears correct to the naked eye.
Required heat treatment adjustments noted on this run sheet
The supply condition listed on the cert dictates what heat treatment steps are needed before you pass the parts to the next station, and all required adjustments are noted on this run sheet for easy reference. If the cert says the material was supplied in a normalized condition, you do not need to run a pre-heat cycle before machining, but you do need to note that on this run sheet so the heat treat team knows they need to run the full quench and temper cycle after your work is complete. If the material was supplied pre-hardened, you adjust your tooling to account for the higher tensile strength, and mark that adjustment in the designated field on this run sheet so the next operator does not adjust the tooling unnecessarily when they take over the lot. Illustrative example: A supply condition of HRAP (hot rolled annealed and pickled) comes with a surface roughness rating of 250 microinches, so you do not waste time running a finishing pass over surfaces that will be welded and ground later anyway.
Tolerance deviations marked on this processing sheet
Minor deviations from standard tolerance ranges can be expected based on the supply condition of the metal, and this processing sheet gives you designated fields to note those deviations before you begin machining. For example, if the cert lists a slight bow in the bar stock that falls within the acceptable supply condition range, you note the maximum bow measurement on this processing sheet so you can adjust your fixturing to account for it, and so the inspection team knows the bow is not a result of your machining work. You never alter the cert data itself, you only note relevant deviations on this processing sheet to keep all job data tied to the specific operations you perform. If the deviation falls outside the acceptable supply range, you flag the lot for review before proceeding, as machining out of spec stock will result in parts that do not meet final performance requirements.
Sign-off fields for this job document
Each sign-off field on this job document corresponds to a check you perform related to the supply condition, so you only sign off once you have confirmed each step is complete and accurate. You sign the first field after you match the lot number, the second after you cross-reference the supply condition to your tooling setup, the third after you note any tolerance deviations, and the fourth after you complete your first test cut and confirm it aligns with the supply condition parameters and part requirements. You never sign off on fields before you complete the corresponding check, even if you have run dozens of identical lots before this one, as minor variations in supply condition can lead to major defects if unaddressed. Each signature is tied to your work on this specific lot, so you ensure all data is accurate before you move on to full production runs for the remaining bars in the lot.
Next shift review of this same supply tracking sheet
When you pick this sheet up at the start of your next shift, or when the next operator picks it up to continue work on the lot, the first step is to cross-reference the sign-offs you added to the cert on file to confirm no changes were made to the supply condition data after you completed your work. You check that no new notes were added to the sheet that would alter your tooling setup or machining parameters, and you re-match the lot number to the bar stock to confirm no one swapped the material between shifts. If you are continuing work on partially machined parts, you cross-reference the supply condition data to the test cuts you made in the previous shift to confirm all parts fall within the required tolerance ranges before you proceed with additional machining. You also check that any deviation notes you added previously are still visible and have not been altered, as those notes are critical for the inspection and heat treatment steps that come after machining is complete. If you find any changes to the sheet that you did not make, you flag the sheet and the lot for a production coordinator to review before you touch any of the material or adjust the machine setup.
