The packet is clipped to the bin. The job number is the first line. You run a finger along the raised ink of the printed number to confirm it matches the scrawl on the bin’s masking tape label, no transposed digits, no swapped prefix for the alloy run. The edge of the traveler is crinkled where the previous shift lead signed off on material receipt, so you know you’re working from the latest active copy, no stale revision floating around.
This Traveler’s Cross-Check Against Material Cert Documentation
In this section, you align every listed material spec on the traveler to the hard copy cert tucked in the back of the packet, no shortcuts, no relying on memory from the last similar run. Follow these steps to complete the cross-check before you load any stock into the CNC mill:

- Locate the 6-digit lot number printed on the top right of the cert, and mark the matching box on the lower left of the traveler’s first page with a blue shop marker, no red ink allowed to avoid confusion with non-conformance marks.
- Confirm the alloy grade listed on the cert matches the grade noted next to the job number on the traveler, paying special attention to suffixes that indicate temper or corrosion resistance treatment.
- Cross-reference the total stock weight listed on the cert to the required run quantity noted on the traveler to confirm you have enough material to complete all 120 parts without pausing mid-run for a restock.
- Initial and date the small box directly below the job number on the traveler to indicate you completed the cross-check, and tuck the cert back into the sealed pocket on the back of the packet to avoid loss or smudging during operation.
Illustrative example: For job number 4729-B, the cert lot number is 827194, the alloy grade is 6061-T6, and the total stock weight of 18 pounds is sufficient to produce the full run of 120 2-ounce brackets with 3 pounds of leftover material for test cuts. If you spot any mismatch at any step, you flag the packet and set it on the Traveler Desk for the production scheduler to review before you touch any of the stock in the bin. You never mark over or alter any pre-printed information on the traveler, even if you believe a spec is listed incorrectly, to preserve the original record for review.
First Piece Dimensional Verification Logged Directly On This Traveler
After you complete the cross-check and load the stock into the mill, you run the first test part immediately, before starting the full production run. You bring the first piece right to the coordinate measuring machine to check all 7 critical dimensions, each of which has a dedicated field on the traveler’s second page. You don’t round any measurements to the nearest thousandth unless the spec explicitly allows for it, you write the exact measured value in each corresponding field, even if it falls well within the acceptable tolerance range. For example, if the inner bore diameter spec is 0.500 inches +/- 0.002 inches, you write 0.5012 inches instead of rounding to 0.501, to leave a clear paper trail for downstream inspection teams.
You also note any test cut adjustments you made to the mill settings between the initial rough cut and the final finish cut in the blank notes section below the dimensional fields, so anyone following your work understands exactly how you arrived at the final first piece dimensions. You affix the physical first piece to the back of the traveler using a small zip tie through the pre-drilled mounting hole, so it stays with the document for the full lifecycle of the run, no chance of it being mixed in with the rest of the production batch. Once all measurements are logged, you have the on-shift quality tech sign off next to each dimension before you proceed with the full run, so there is no ambiguity about the first piece’s adherence to specs later on.
Cert Match Confirmation Stamped In The Margin Of This Traveler
After the full run is complete and all parts are deburred and set in the clean holding bin, you pull the cert out of the back pocket of the traveler one more time to confirm that the material test results for hardness and tensile strength align with the part performance requirements listed on the traveler’s third page. You don’t need to copy the full test results onto the traveler, you just use the steel “CERT MATCH” stamp kept in the bench tool caddy to mark the right margin of the third page, directly next to the performance requirements line. You add your initials next to the stamp, so there is a clear record of who completed the final cert alignment check.
If any test result falls outside the listed requirement, you flag the run and set the entire packet aside for the material engineer to review, no exceptions, even if all dimensional checks passed for every part in the run. You also count the total number of good parts produced, the number of scrap parts from test cuts and mid-run adjustments, and write those two numbers in the designated fields at the bottom of the third page, so the inventory team can reconcile the run output against the initial material quantity without digging through extra paperwork. You tuck the cert back into the sealed pocket once this check is complete, and clip the traveler to the holding bin with the finished parts before moving the bin to the inspection queue.
When You Pull This Traveler For Final Batch Reconciliation
This is the next time you interact with this document, after the full batch has moved through final inspection and is waiting to be packed for shipment. You will pull this traveler from the completed run file to cross-check all logged values against the final inspection report, before the batch is cleared for movement. You will confirm that the initial lot number you marked on the first page matches the lot number noted on the final inspection report, that the first piece dimensional checks align with the random sample check results from the inspection team, and that the CERT MATCH stamp is present and initialed in the correct margin.
You will also cross-check the total good part count you logged against the count noted by the inspection team, to resolve any discrepancies before the parts leave the facility. If all values align, you will sign and date the final signoff field at the very bottom of the traveler, and tuck the full packet into the archived job file, where it will stay for 7 years per internal record keeping requirements. If you spot any gaps or mismatches during this final check, you will pull the corresponding run logs from the CNC mill to fill in missing information or resolve count discrepancies, so the full record is complete before archiving. You will not add any notes or marks to the traveler after the final signoff is complete, to preserve the integrity of the run record for future reference if a part performance question arises later. You will file the traveler in the correct numbered job folder, so it is easy to locate if it is needed for review down the line.
